I used a coaster design from EmbroideryIt.com
I wanted to share the steps I took to make a pocket on the back of the coaster to hold a gift card. I wanted them to be used as ornaments in the future, so I included a ribbon for hanging.
The photos show the steps I took to make these.
1. Finish the front of the coaster embroidery. Leave it in the hoop.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhOiUZCyaVS0MWSYvEGQgDu4yTI-b90N8m8DDoBSWlQ7FdTX6Mh5SA8msP9wwegMe0Izf41jrb8YKFr7nDmGqXneVC7JLSs8WgT1oRQSKNj3twaq20OJSUrPmD65Mz4xV4bKdMUGwRCTDM/s320/20171216_214705.jpg)
2. Cut the felt backing piece about 1/3 of the way from one edge.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhon47USkLCSNHbMBLdtppumVQk7jBawQ5EO4RIaQw9WzAXkbAXEt4h52zRlru_623lF9cjIK5ehBM8g4LjVE2_P-j0uKgMe3AP_DBDb6Yyvspplw8JWluriKOtJoy_OdaT2eXaCEI7czk/s320/backcut.jpg)
3. Turn the hoop over to see the back side.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEgq7GriEqVa8sUr1sTgJXw-Talt3dtaDhN0nCEMukXFvqq1kKuZuiec8mNXbdE5GoV43MTqq_hI3GUf6AyZh5p9aTZpBfBcGTRf8DXt2PO4u5tS_2BAya5KOA1lEcI3mvPCQN76oktbWes/s320/20171216_214718.jpg)
4. Place the ribbon ends into the embroidered area, below the stitching line. Place tape over the ribbon, 1/2 inch above the stitched line on the stabilizer (see larger image). Line up the larger felt backing piece along the bow line.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhgwsI08YCa3Njd-PN3JnHIJaHcug8WuN7jaX7RvvkN78g9QzAxpoY5EXqy-ssmuvisOmUBdiucCxLGHuHx9XnNxGg3qUdHGth3cBWlhCfeTbv7Oix9ghb4tYL7oPvGOUknB680iOYVJ2o/s320/lower.jpg)
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEik9MyvhUU7khDv9v3Sm6JHX_ru6o3b_bgvG7QM7atbk2a7ynRoLV3bGjLpLuIq2_66pCzXYq_h1bsyjBijA6-33nqPkvYVqjo6MzMNfH4GpqGNk2n59QOxQ7nQ9cHPq9GD4AQ481vjpgI/s320/closeupribbon.jpg)
5. Align the top 1/3 of the felt backing to the bottom section and tape them together in the middle so there is no gap between them. Then tape the sides where the cut lines meet. Finally, tape down the corners.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEhP1gIkDfyBnKX8LD5CMWWPC8nspZhFnzhIupZ4JS1rYy8l765tjwsk-IfcHjBtiPSVx2vtAgaI-1CxbnW6yi2g4uxGDcgT3Sb_7gAUEpXTy7z1bZf9oYjarhKMx8xqV9J5sDVzc_oUsxk/s320/tapedribbon.jpg)
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEgCva39zTXngSll6bvbOZ1aO5uoHYx1HnUkS2h_zvLzRhw8UM9zNZe8K0fSfucrbLh-ZRlMCTJjRLCdF6EmZiwzHG7eFt_roGuOFqEeh__mLstOz-YoC5VsGZmUFqh5cQ0oc_KWvDjDlEo/s320/alltaped.jpg)
6. Place the hoop back into the embroidery machine to finish the final edge stitch that holds the front and back together. Remove the embroidery from the hoop and carefully remove the tear-away stabilizer.
![](https://blogger.googleusercontent.com/img/b/R29vZ2xl/AVvXsEghWssjqqCWUYR_9XGHNwnVTWBm3TOywaRxklBzevS1rftRrda9A9LCGXaDsPqZ_8ID917jWFqtWC__kUzR6A8DqAF3e0AVO4crhPmkfe4_IxS6wUPtrXYoFEE2KZqv1tVjEvO4wLpbT6g/s320/tearaway.jpg)
7. Trim the sides and bottom 1/4 inch from the stitched border. Trim the top back edge, without cutting the ribbon, by folding the front piece of felt and the ribbon down to the front of the embroidery. Trim 1/4 inch beyond the stitched edge.
8. Trim the front piece of felt 1/4 inch from the stitching, making sure to fold the ribbon down to the back keeping it away from the scissors.
9. That's it. Finished and ready for gifting.
No comments:
Post a Comment